A review on gas turbines derived from aero engines

Shahrzad Mozafari Ghazafi

Abstract


The process of designing and manufacturing turbine engines has many complications and going through this process requires significant time and costs. Therefore, reputable gas turbine manufacturing companies have made a lot of efforts to shorten the design and manufacturing processes, one of these ways is to use air gas turbine cores to build industrial gas turbines. This category of industrial gas turbine is called derived gas turbine. Considering the special characteristics of air gas turbines such as light weight, relatively small dimensions, high efficiency and performance, if the gas generator core of these turbines is used for the industrial gas turbine core, in addition to shortening the design and manufacturing process, it can be desired need to obtain an industrial gas turbine was achieved. In this study, the main types of gas turbines derived from air engines have been reviewed and the characteristics of each of them have been discussed.


Keywords


Industrial gas turbine, derived gas turbine, modified engine, turbine engines, gas generator

Full Text:

PDF

References


Poullikkas, A. (2005). An overview of current and future sustainable gas turbine technologies.Renewable and Sustainable Energy Reviews, 9(5), 409-443.

Li, Y. G. (2002). Performance-analysis-based gas turbine diagnostics: A review. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 216(5), 363-377.

Liu, Z., & Karimi, I. A. (2020). Gas turbine performance prediction via machine learning. Energy, 192, 116627.

Doustdar, M. M., & Aminjan, K. K. (2019). Modeling the Thrust and Specific Fuel Consumption for a Hypothetical Turbojet Engine. International Journal of IC Engines and Gas Turbines, 5(1), 45-52.

Zarepour, G., & Aminjan, K. K. (2018). Modeling the Thrust and Specific Fuel Consumption for a Hypothetical Turbofan Engine. International Journal of IC Engines and Gas Turbines, 4(1), 1-10.

Ghazafi, S. M. (2022). Study on the Evolution of Drone Engine and the Future of Drone Propulsion. International Journal of IC Engines and Gas Turbines, 8(1), 10-19.

Navid Heydari. Investigation Various Types of Power Plants from Economic, Technical and

Environmental Aspects. International Journal of I.C. Engines and Gas Turbines. 2022; 8(1): 1–9p.

Ali Kamranpey. Study on Effects of Mass Flow Rate and Compressor Pressure Ratio on Gas Turbine Cycle Performance. International Journal of I.C. Engines and Gas Turbines. 2022; 8(2): 1–0p7.

Azizi, M. A., & Brouwer, J. (2018). Progress in solid oxide fuel cell-gas turbine hybrid power systems:System design and analysis, transient operation, controls and optimization. Applied energy, 215, 237-289.

Aminjan, K. K., Rahmanivahid, P., & Heidari, M. Effects of Thermodynamic Parameters On Performance Of Gas Turbine Cycle With Regenerator.

Heydari, A., & Doustdar, M. M. (2020). Effects of Compressor Pressure Ratio and Combustion Chamber Exhaust Gases Temperatures on Gas Turbine Cycle Performance. International Journal of IC Engines and Gas Turbines, 6(1), 1-6.

Rahman Amiri et al. Conceptual design of an industrial gas turbine derived from an air engine. The 18th conference of Iran Aerospace Society. 2020.

Oswald, A. D., & Hiner, S. D. (2006, January). More Efficient Applications for Naval Gas Turbines: Addressing the Mismatch Between Available Technology and the Requirements of Modern Naval Gas Turbine Inlets. In Turbo Expo: Power for Land, Sea, and Air (Vol. 42401, pp. 35-46).

Mahmoodi, M., & Aminjan, K. K. (2017). Numerical simulation of flow through sukhoi 24 air inlet.Computational Research Progress in Applied Science & Engineering (CRPASE), 3.

Hashmi, M. B., Abd Majid, M. A., & Lemma, T. A. (2020). Combined effect of inlet air cooling and fouling on performance of variable geometry industrial gas turbines. Alexandria Engineering Journal,59(3), 1811-1821.

Parhrizkar, H., Aminjan, K. K., Doustdar, M. M., & Heydari, A. (2019). Optimization of S-Shaped Air Intake by Computational Fluid Dynamics. International Journal of Fluid Mechanics & Thermal Sciences, 5(2), 36.

Ameri, M., Shahbazian, H. R., & Nabizadeh, M. (2007). Comparison of evaporative inlet air cooling systems to enhance the gas turbine generated power. International journal of energy research, 31(15), 1483-1503.

Aminjan, K. K. (2018). A Review on the Change Process and the Evolution of Aircraft Engine Air Intake. International Journal of Mechanics and Design, 4(1), 15-22.

Alqallaf, J., Ali, N., Teixeira, J. A., & Addali, A. (2020). Solid particle erosion behaviour and protective coatings for gas turbine compressor blades—A review. Processes, 8(8), 984.

Lin, A., Zheng, Q., Jiang, Y., Lin, X., & Zhang, H. (2019). Sensitivity of air/mist non-equilibrium phase transition cooling to transient characteristics in a compressor of gas turbine.International Journal of Heat and Mass Transfer, 137, 882-894.

Farrahi, G. H., Tirehdast, M., Abad, E. M. K., Parsa, S., & Motakefpoor, M. (2011). Failure analysis of a gas turbine compressor. Engineering Failure Analysis, 18(1), 474-484.

Gicquel, L. Y., Staffelbach, G., & Poinsot, T. (2012). Large eddy simulations of gaseous flames in gas turbine combustion chambers. Progress in energy and combustion science, 38(6), 782-817.

Boudier, G., Gicquel, L. Y. M., Poinsot, T., Bissieres, D., & Bérat, C. (2007). Comparison of LES, RANS and experiments in an aeronautical gas turbine combustion chamber. Proceedings of the Combustion Institute, 31(2), 3075-3082.

Bulat, G., Jones, W. P., & Marquis, A. J. (2014). NO and CO formation in an industrial gas-turbine combustion chamber using LES with the Eulerian sub-grid PDF method. Combustion and Flame, 161(7), 1804-1825.

Alajmi, A. E. S. E. T., Adam, N. M., Hairuddin, A. A., & Abdullah, L. C. (2019). Fuel atomization in gas turbines: A review of novel technology. International Journal of Energy Research, 43(8), 3166-3181.

Khani Aminjan, K., Kundu, B., & Ganji, D. D. (2020). Study of pressure swirl atomizer with tangential input at design point and outside of design point. Physics of Fluids, 32(12), 127113.

Khani Aminjan, K., Heidari, M., & Rahmanivahid, P. (2021). Study of spiral path angle in pressure- swirl atomizer with spiral path. Archive of Applied Mechanics, 91(1), 33-46.

Dahm, W. (2002). Fundamental analysis of liquid atomization by fuel slingers in small gas turbines.In 32nd AIAA fluid dynamics conference and exhibit (p. 3183).

Aminjan, K. K., Ghodrat, M., Escobedo-diaz, J. P., Heidari, M., Chitt, M., & Hajivand, M. (2022).Study on inlet pressure and Reynolds number in pressure-swirl atomizer with spiral path. International Communications in Heat and Mass Transfer, 137, 106231.

Ali Kamranpey. Review on Main Equations for Measuring Spray Properties in Centrifugal Injectors.Journal of Industrial Safety Engineering. 2021; 8(3): 17–23p

Khani Aminjan, K., Heidari, M., Ganji, D. D., Aliakbari, M., Salehi, F., & Ghodrat, M. (2021). Study of pressure-swirl atomizer with spiral path at design point and outside of design point. Physics of Fluids, 33(9), 093305.

Doustdar, M. M., Alipour, H., & Aliakbari, M. (2022). Estimating Spray Characteristics of the Air-Blast atomizer of a Typical Jet Engine using Definition of the New Non-dimensional Number K:Numerical and Experimental Study. Tehnički vjesnik, 29(1), 208-214.

Kiumars Khani Aminjan, Mohammad Mahdi Heydari, Esmail Valizadeh. 2018. Numerical Analysis of the 3D Flow in Swirl Injector with Spiral Paths. Computational Research Progress in Applied Science & Engineering.

Shanmugadas, K. P., Chakravarthy, S. R., Chiranthan, R. N., Sekar, J., & Krishnaswami, S. (2018). Characterization of wall filming and atomization inside a gas-turbine swirl injector. Experiments in Fluids, 59(10), 1-26.

Jenish, I., Appadurai, M., & Raj, E. F. I. (2021). CFD Analysis of modified rushton turbine impeller. Int. J. Sci. Manag. Stud. (IJSMS), 4, 8-13.

Aminjan, K. K., Heidari, M., Rahmanivahid, P., Alipour, H., & Khashehchi, M. (2021). Design and Simulation of Radial Flow Turbine Impeller and Investigation Thermodynamic Properties of Flow in LE and TE.

Yang, J., Zhao, F., Zhang, M., Liu, Y., & Wang, X. (2021). Numerical Analysis of Labyrinth Seal Performance for the Impeller Backface Cavity of a Supercritical CO2 Radial In flow Turbine. Computer Modeling in Engineering & Sciences, 126(3), 935-953.

Zhou, Q., Yin, Z., Zhang, H., Wang, T., Sun, W., & Tan, C. (2020). Performance analysis and optimized control strategy for a three-shaft, recuperated gas turbine with power turbine variable area nozzle. Applied Thermal Engineering, 164, 114353.

Matsunuma, T., Yoshida, H., Iki, N., Ebara, T., Sodeoka, S., Inoue, T., & Suzuki, M. (2005, January). Micro gas turbine with ceramic nozzle and rotor. In Turbo Expo: Power for Land, Sea, and Air (Vol.46997, pp. 973-979).

Kulor, F., Markus, E. D., & Kanzumba, K. (2021). Design and control challenges of hybrid, dual nozzle gas turbine power generating plant: A critical review. Energy Reports, 7, 324-335.

Goward, G. W. (1998). Progress in coatings for gas turbine airfoils. Surface and coatings technology,108, 73-79.

Talya, S. S., Rajadas, J. N., & Chattopadhyay, A. (2000). Multidisciplinary optimization for gas turbine airfoil design. Inverse Problems in Engineering, 8(3), 283-308.

Heidari, M., Rahmanivahid, P., & Aminjan, K. K. (2020). Aerodynamic Analysis of Double Wedge Airfoil 16.5%@ 50% in Different Angle of Attack at Supersonic Flow. Solid State Technology, 63(6).

Martini, P., Schulz, A., & Bauer, H. J. (2006). Film cooling effectiveness and heat transfer on the trailing edge cutback of gas turbine airfoils with various internal cooling designs.

Aminjan, K. K. (2018). Aerodynamic Analysis of NACA 65-2012 Airfoils at Different Attack Angles with Computational Fluid Dynamics (CFD) Method. International Journal of Mechanical Handling and Automation, 4(2), 9-16.

Kamranpay, A., & Mehrabadi, A. Numerical Analysis of NACA Airfoil 0012 at Different Attack Angles and Obtaining its Aerodynamic Coefficients.

Horbach, T., Schulz, A., & Bauer, H. J. (2011). Trailing edge film cooling of gas turbine

airfoils—external cooling performance of various internal pin fin configurations.

Feng, Z., Liu, Z., Shi, Y., & Wang, Z. (2016). Effects of hot streak and airfoil clocking on heat transfer and aerodynamic characteristics in gas turbine. Journal of Turbomachinery, 138(2).

Akbari, P. (2021). Study of NACA 6212 Airfoil and Investigation of its Aerodynamic Properties in Different Angles of Attack. International Journal of Mechanical Dynamics & Analysis, 7(1), 43-49p.

Montis, M., Niehuis, R., & Fiala, A. (2010, October). Effect of surface roughness on loss behaviour, aerodynamic loading and boundary layer development of a low-pressure gas turbine airfoil. In Turbo Expo: Power for Land, Sea, and Air (Vol. 44021, pp. 1535-1547).

Sayyaadi, H., & Mehrabipour, R. (2012). Efficiency enhancement of a gas turbine cycle using an optimized tubular recuperative heat exchanger. Energy, 38(1), 362-375.

Wilson, D. G. (1984). Design of high-efficiency turbomachinery and gas turbines.

Stepanov, O. A., Rydalina, N. V., Antonova, E. O., Aksenov, B. G., Derevianko, O. V., Akhmetova, I. G., & Zunino, P. (2019). The possibility of increasing the operating efficiency of gas turbines at compressor stations of main gas pipelines. International Journal of Civil Engineering and Technology,10(2), 2130-2137.

https://turbina.ir




DOI: https://doi.org/10.37628/ijicegt.v8i2.1479

Refbacks

  • There are currently no refbacks.