Open Access Open Access  Restricted Access Subscription or Fee Access

Numerical Study of Vibration Stress and Deformation of Rotating Fan Blade of a Gas Turbine

kapineepathiah janardhana, S. K. Maharana

Abstract


The vibration stress caused by resonance is the main cause of failure in aircraft engine blades. The study is aimed at investigating the vibration stress of a single-stage fan blade influenced by the interaction of aerodynamic and structural behavior at multiple critical speeds. A three-dimensional finite element model of the blade was developed for the simulation of vibration stress and its subsequent effects. The blade was verified by modal test. This was to understand the response of the blade when it resonates. The intent was to locate the measure the deformation at a specific location and understand the cause of the strain .It was also observed during the study that there is no positive correlation between the peak stress and critical speed, while it is determined by the comprehensive action of critical speed, vibration mode and synchronous excitation. The peak stress distribution is closely linked to the mode shape of the blade, and it always appears at the leading edge and changes along the blade height. It also illustrates that the leading edge of the blade is most prone to vibration fatigue.
The optimization of the dynamic characteristics shall be done through the optimization toolbox of commercially available MATLAB software. The study of the optimized set of characteristics shall throw light upon the vibration related high cycle fatigue generated for a rotating fan blade. A series of computational modeling methods, using available theoretical backgrounds of stress development, of vibration stress [ hence the deformation ] and optimization techniques to obtain the stress that develop the numerically-determined deformation shall be compared and the findings be presented through the research.

Full Text:

PDF

References


Kumar D, Barad S and Suresh TN. , Gas turbine blade damper: A design optimization study to mitigate high resonance blade vibration, ASME 2013 Gas turbine India conference, Bangalore, Karnataka, India, 5–6 December 2013, V001T05A018.

Ni K, Wang XQ and Mignolet M., Blade stress estimation during multiple vibratory modes, Structures, structural dynamics, and materials and co-located conferences, 8–11 April 2013, Boston, Massachusetts, pp.2013–1772.

Aziz I, Tarar W, Akhtar I, et al., Vibration stress suppression in turbine blades subjected to aerodynamic loading, The ASME 2013 international mechanical engineering congress and exposition, 15–21 November 2013, San Diego, California, USA, IMECE2013-63724.

Zhang D, Hong J, Ma Y, et al., A probability method for prediction on high cycle fatigue of blades caused by aerodynamic loads. Adv Eng Software( 2011), 42:1059–1073.

Ramakrishnan K. , Computational investigations of axial and radial flow compressor aeromechanics. PhD Thesis, Purdue University, USA, 2005.

Welch GE, McVetta AB, Stevens MA, et al., Variable speed power-turbine research at Glenn Research Center. NASA(2012), 2012-217605.

Horsley J. The rolls-royce way of validating fan integrity. AIAA-1993-2602(1993) p.1–9.

Sayer R J., Finite element analysis- a numerical tool for machinery vibration analysis, Sound and Vibration (2004), pp.18-24

Brown K W, Hirschbein M S, Chamis C C, Finite element engine blade structural optimization. AIAA-1985,p p.793–803.

Berzeri M, Shabana AA., Study of the centrifugal stiffening effect using finite element absolute nodal coordinate formulation, Multibody System Dynamics (2002), 7, pp. 357–87.

Mayo JM, Garcia-Vallejo D, Dominguez J., Study of geometric stiffening effects: a comparison of different formulations, Multibody System Dynamics (2004),11, pp. 321–41.

Carney KS, Pereira JM, Revilock DM, Matheny P, Jet engine fan blade containment using alternate geometry, Int. Jou. of Impact Engineering,(2009),36,pp. 720–728.

Meherwan PB., Gas turbine engineering handbook, Boston, MA, USA: Gulf Professional Publishing( 2006).

Satter SA, Stargardter H., The development of JT8D turbofan engine composite fan blades. AIAA 69-465, (1969),pp. 1–6.

Cai J, Xu Q, Wang Z., Flutter analysis of compressor blade based on CFD/CSD, Applied Mechanics and Materials(2011),50–51, pp.8–12.

Kosmatka JB, Appuhn G, Mehmed D. Design and testing of integrally damped first stage composite fan blades. AIAA 2002-1511; 2002. pp. 1–11.

Kielb R, Macri F, Oeth D, Nashif A, Macioce P, Panossian H, Leighley F. Advanced damping systems for fan and compressor blisks, AIAA 1998-3863(1998), pp. 1–7.

Kauffman JL, Lesieutre GA. , Vibration Reduction of Turbomachinery bladed disks with changing dynamics using piezoelectric materials. AIAA-2011(2011),p p. 1–12.

Benjamin C, Kauffman J, Duffy K, Provenza A, Morrison C., Active vibration reduction of titanium alloy fan blades (FAN1) using piezoelectric materials, NASA/TM-2010-216335(2010)

Vahdati M, Sayma AI, Marshall JG, Imregun M., Mechanisms and prediction methods for fan blade stall flutter. Journal of Propulsion and Power( 2011) 17:1100–8.

Anandavel K, Prakash RV., Effect of three-dimensional loading on macroscopic fretting aspects of an aero-engine blade-disc dovetail interface. Tribology International (2011) 44, 1544–55.

Leye M. Amoo , On the design and structural analysis of jet engine fan blade structures,Progress in Aerospace Sciences 60, (2013) 1-11

R Core Team (2013). R: A language and environment for statistical computing. R Foundation for Statistical Computing, Vienna, Austria. ISBN 3-900051-07-0, URL http://www.R-project.org/.

Rula M. Coroneos, Structural Analysis and Optimization of a Composite Fan Blade for Future Aircraft Engine(2012), Glenn Research Center, Cleveland, Ohio, NASA/TM—2012-217632


Refbacks

  • There are currently no refbacks.